fix cyd_35r backlight/GT911 for ESP32-3248S035C (BL=27).

Wrong TFT_BL=21 caused black screens; INT is separate from backlight. Rebuild, flash COM3, and ship firmware/cyd_35r package.

Co-authored-by: Cursor <cursoragent@cursor.com>

README.md

@@ -4,9 +4,16 @@ GPIO22 读人体红外（PIR）模块 OUT：每次检测到运动开始，屏幕
 
 ## 硬件
 
+| 项目 | 2.8"（默认） | 3.5" C |
+|------|-------------|--------|
+| 板子 | ESP32-2432S028R | ESP32-3248S035C |
+| 屏 / 触控 | ILI9341 + XPT2046 SoftSPI | ST7796 + GT911 I2C |
+| 背光 | GPIO21 | GPIO27 |
+| PIR OUT | **GPIO22**（两板相同） | **GPIO22** |
+| PlatformIO | `cyd` | `cyd_35r` |
+
 | 项目 | 说明 |
 |------|------|
-| 板子 | CYD ESP32-2432S028R |
 | 模块 | 三脚小型人体红外（卖家常写 mini SR501，实际多为 **HC-SR505**） |
 | 供电 | **3.3V**（本工程已实测可用） |
 | 输出 | **GPIO22** |
@@ -32,7 +39,7 @@ GPIO22 读人体红外（PIR）模块 OUT：每次检测到运动开始，屏幕
 注意：
 
 - 上电后约 **30～60 秒** 预热，此前可能无反应或乱跳
-- OUT 接 **GPIO22**（勿接 21 背光），必须共地
+- OUT 接 **GPIO22**（2.8 勿接 21 背光；3.5 勿接 27 背光），必须共地
 - 小模块一般无灵敏度旋钮；检测距离大约 3m 量级
 
 ## 操作
@@ -43,14 +50,23 @@ GPIO22 读人体红外（PIR）模块 OUT：每次检测到运动开始，屏幕
 ## 构建 / 烧录
 
 ```bash
+# 2.8"
 pio run -e cyd -t upload
+
+# 3.5" C
+pio run -e cyd_35r -t upload
 ```
 
 预编译包：
 
 ```powershell
+# 2.8"
 cd firmware\cyd
 .\flash.ps1
+
+# 3.5"
+cd firmware\cyd_35r
+.\flash.ps1
 # 或 .\flash.ps1 -Port COMx
 ```
 
@@ -58,4 +74,5 @@ cd firmware\cyd
 
 ```powershell
 .\firmware\export_from_build.ps1
+.\firmware\export_from_build.ps1 -Env cyd_35r
 ```

firmware/README.md

@@ -1,15 +1,22 @@
 # 预编译固件
 
-目录：[`cyd/`](cyd/)
+| 目录 | 板子 |
+|------|------|
+| [`cyd/`](cyd/) | **2.8"** ESP32-2432S028R（ILI9341 + XPT2046） |
+| [`cyd_35r/`](cyd_35r/) | **3.5" C** ESP32-3248S035C（ST7796 + GT911，BL=27） |
 
-板子：**CYD ESP32-2432S028R**（ILI9341）  
+功能：小型人体红外 SR505/mini SR501（GPIO22、3.3V）计数 + 触控 + LVGL
-功能：小型人体红外 SR505/mini SR501（GPIO22、3.3V）计数 + SoftSPI 触控 + LVGL
 
 ## 刷写
 
 ```powershell
+# 2.8"
 cd firmware\cyd
 .\flash.ps1
+
+# 3.5"
+cd firmware\cyd_35r
+.\flash.ps1
 # 或 .\flash.ps1 -Port COM3
 ```
 
@@ -17,5 +24,7 @@ cd firmware\cyd
 
 ```powershell
 .\firmware\export_from_build.ps1
+.\firmware\export_from_build.ps1 -Env cyd_35r
 .\firmware\export_from_build.ps1 -SkipBuild
+.\firmware\export_from_build.ps1 -Env cyd_35r -SkipBuild
 ```

firmware/cyd_35r/VERSION.txt

@@ -0,0 +1,15 @@
+name: CYD humanInfraredModuletest (cyd_35r)
+git: d5b37d0
+date: 2026-10-25
+board: ESP32-3248S035 (ST7796)
+flash_size: 4MB
+offsets:
+  0x1000  bootloader.bin
+  0x8000  partitions.bin
+  0xe000  boot_app0.bin
+  0x10000 firmware.bin
+sha256:
+  bootloader.bin  3D234A7471F67B013686DABD4DEE7C1FA915C9928463616A94BC9297ACF1ABF8
+  boot_app0.bin   F94C5D786A7A8FAB06AC5D10E33BF37711A6697636DC037559EA19CC410A17F0
+  firmware.bin    BBD98BD91197C777FD453E7427CBCF4A5B385728FA7D7E9D52F9437899CEC874
+  partitions.bin  148B959CBFF1C38AA8E1D5C0BA9D612C54997B945E56A63F41223EEF650653A1

firmware/cyd_35r/flash.bat

@@ -0,0 +1,5 @@
+@echo off
+setlocal
+cd /d "%~dp0"
+powershell -NoProfile -ExecutionPolicy Bypass -File "%~dp0flash.ps1" %*
+exit /b %ERRORLEVEL%

firmware/cyd_35r/flash.ps1

@@ -0,0 +1,98 @@
+# Flash archived CYD TF+Speaker firmware (no rebuild needed)
+# Usage:
+#   .\flash.ps1
+#   .\flash.ps1 -Port COM5
+#   .\flash.ps1 -Port COM5 -Baud 460800
+
+param(
+  [string]$Port = "",
+  [int]$Baud = 921600
+)
+
+$ErrorActionPreference = "Stop"
+$here = Split-Path -Parent $MyInvocation.MyCommand.Path
+Set-Location $here
+
+function Find-Esptool {
+  $pio = Get-Command pio -ErrorAction SilentlyContinue
+  if (-not $pio) {
+    $pioPath = Join-Path $env:USERPROFILE "AppData\Local\Programs\Python\Python312\Scripts\pio.exe"
+    if (Test-Path $pioPath) {
+      $env:Path = "$(Split-Path $pioPath);$env:Path"
+      $pio = Get-Command pio -ErrorAction SilentlyContinue
+    }
+  }
+  if ($pio) {
+    $pkg = Join-Path $env:USERPROFILE ".platformio\packages\tool-esptoolpy\esptool.py"
+    if (Test-Path $pkg) { return @{ Kind = "py"; Path = $pkg } }
+  }
+  $py = Get-Command python -ErrorAction SilentlyContinue
+  if ($py) {
+    try {
+      & python -c "import esptool" 2>$null
+      if ($LASTEXITCODE -eq 0) { return @{ Kind = "mod"; Path = "esptool" } }
+    } catch {}
+  }
+  $esp = Get-Command esptool.py -ErrorAction SilentlyContinue
+  if ($esp) { return @{ Kind = "py"; Path = $esp.Source } }
+  return $null
+}
+
+if (-not $Port) {
+  $ports = @()
+  try {
+    Add-Type -AssemblyName System.IO.Ports -ErrorAction SilentlyContinue | Out-Null
+    $ports = [System.IO.Ports.SerialPort]::GetPortNames() | Sort-Object
+  } catch {}
+  if (-not $ports -or $ports.Count -eq 0) {
+    $ports = Get-CimInstance Win32_SerialPort -ErrorAction SilentlyContinue |
+      Select-Object -ExpandProperty DeviceID | Sort-Object
+  }
+  if (-not $ports -or $ports.Count -eq 0) {
+    Write-Error "No serial ports found. Plug in the CYD USB cable, then retry with -Port COMx"
+  }
+  if ($ports.Count -eq 1) {
+    $Port = $ports[0]
+  } else {
+    Write-Host "Available ports: $($ports -join ', ')"
+    $Port = $ports[-1]
+    Write-Host "Using last port: $Port (override with -Port)"
+  }
+}
+
+$tool = Find-Esptool
+if (-not $tool) {
+  Write-Error "esptool not found. Install PlatformIO (`pio`) or: pip install esptool"
+}
+
+$needed = @("bootloader.bin", "partitions.bin", "boot_app0.bin", "firmware.bin")
+foreach ($f in $needed) {
+  if (-not (Test-Path (Join-Path $here $f))) {
+    Write-Error "Missing $f — run ..\export_from_build.ps1 from repo root first"
+  }
+}
+
+$argsCommon = @(
+  "--chip", "esp32",
+  "--port", $Port,
+  "--baud", "$Baud",
+  "--before", "default_reset",
+  "--after", "hard_reset",
+  "write_flash", "-z",
+  "--flash_mode", "dio",
+  "--flash_freq", "40m",
+  "--flash_size", "4MB",
+  "0x1000", "bootloader.bin",
+  "0x8000", "partitions.bin",
+  "0xe000", "boot_app0.bin",
+  "0x10000", "firmware.bin"
+)
+
+Write-Host "Flashing $here -> $Port @ $Baud"
+if ($tool.Kind -eq "mod") {
+  & python -m esptool @argsCommon
+} else {
+  & python $tool.Path @argsCommon
+}
+if ($LASTEXITCODE -ne 0) { exit $LASTEXITCODE }
+Write-Host "Done. Open serial monitor at 115200 if needed."

firmware/cyd_35r/media/preview.html

@@ -0,0 +1,53 @@
+<!DOCTYPE html>
+<html lang="en">
+<head>
+<meta charset="utf-8" />
+<title>Human IR</title>
+<style>
+
+  *{box-sizing:border-box;margin:0;padding:0}
+  html,body{width:320px;height:240px;overflow:hidden;background:#000;margin:0}
+  .bezel{width:320px;height:240px;background:#1a1408}
+  .screen{width:320px;height:240px;background:#0A1016;color:#EAF0F6;font:12px/1.2 system-ui,sans-serif;position:relative;overflow:hidden}
+  .muted{color:#7A8B9C}.ok{color:#3DDC97}.bad{color:#E85D4C}.acc{color:#4FC3F7}.amber{color:#FFB74D}
+  .btn{border:0;border-radius:8px;background:#243140;color:#EAF0F6;font-weight:600}
+  .btn.acc{background:#1A4A6E}.btn.on{background:#1B5E4A}.btn.warn{background:#6B3A1E}
+
+
+  .t{position:absolute;left:0;right:0;top:2px;text-align:center;font-size:26px;font-weight:700}
+  .pin{position:absolute;left:0;right:0;top:34px;text-align:center}
+  .cnt{position:absolute;left:0;right:0;top:56px;text-align:center;font-size:42px;font-weight:800;color:#4FC3F7}
+  .hint{position:absolute;left:0;right:0;top:104px;text-align:center}
+  .st{position:absolute;left:0;right:0;top:122px;text-align:center;font-size:16px;font-weight:700;color:#FF7043}
+  .hold{position:absolute;left:0;right:0;top:144px;text-align:center;font-size:11px}
+  .bar{position:absolute;left:24px;right:24px;top:162px;height:10px;background:#1A2430;border-radius:4px;overflow:hidden}
+  .bar>i{display:block;height:100%;width:28%;background:#FF7043}
+  .raw{position:absolute;left:0;right:0;top:176px;text-align:center;font-size:11px}
+  .act{position:absolute;left:24px;right:24px;bottom:8px;height:40px}
+
+
+/* CYD 3.5" full-bleed: non-uniform scale matches firmware UX()/UY(). */
+html,body{width:480px!important;height:320px!important;overflow:hidden!important;background:#000!important;margin:0!important;padding:0!important}
+.cyd35-scale{width:320px;height:240px;transform:scale(1.5,1.3333333333);transform-origin:0 0;overflow:hidden}
+</style>
+</head>
+<body>
+<div class="cyd35-scale">
+
+<div class="bezel"><div class="screen" id="s">
+
+  <div class="t">Human IR</div>
+  <div class="pin muted">OUT-&gt;GPIO22  VCC 3.3V</div>
+  <div class="cnt">3</div>
+  <div class="hint muted">detects</div>
+  <div class="st">MOTION</div>
+  <div class="hold muted">hold 1250 ms</div>
+  <div class="bar"><i></i></div>
+  <div class="raw ok">OUT HIGH  act=HIGH</div>
+  <button class="btn act" type="button">Reset</button>
+
+</div></div>
+
+</div>
+</body>
+</html>

firmware/cyd_35r/meta.json

@@ -0,0 +1,19 @@
+{
+  "boardId": "esp32-3248s035",
+  "name": "CYD Human IR (3.5\")",
+  "summary": "Small PIR (SR505/mini SR501) on GPIO22 @ 3.3V: motion-start count +1",
+  "description": "ST7796 + GT911 capacitive + LVGL. BL=GPIO27. VCC 3.3V / GND / OUT->GPIO22. Float INPUT, idle LOW active HIGH. Motion edge +1, hold bar, Reset clears.",
+  "tags": [
+    "pir",
+    "sr505",
+    "human-infrared",
+    "gpio22",
+    "3.3v",
+    "touch",
+    "lvgl",
+    "counter"
+  ],
+  "media": {
+    "preview": "media/preview.html"
+  }
+}

firmware/export_from_build.ps1

@@ -67,21 +67,5 @@ foreach ($h in $hashes) {
 }
 $lines | Set-Content -Encoding utf8 (Join-Path $dst "VERSION.txt")
 
-# Keep / refresh meta.json boardId for catalog filtering
-$metaPath = Join-Path $dst "meta.json"
-if (Test-Path $metaPath) {
-  try {
-    $meta = Get-Content $metaPath -Raw | ConvertFrom-Json
-    $meta.boardId = $boardIdHint
-    if ($Env -eq "cyd_35r" -and $meta.name -notmatch "3\.5") {
-      $meta.name = ($meta.name -replace "\s*$","") + " (3.5\")"
-    }
-    $meta | ConvertTo-Json -Depth 8 | Set-Content -Encoding utf8 $metaPath
-  } catch {
-    Write-Host "meta.json update skipped: $_"
-  }
-} elseif ($Env -eq "cyd_35r") {
-  Write-Host "Note: add firmware/cyd_35r/meta.json with boardId=$boardIdHint for the web catalog"
-}
 
 Write-Host "Exported -> $dst (env=$Env git=$git)"

include/pins.h

@@ -8,19 +8,25 @@
 #define SCREEN_HEIGHT 480
 #define UI_HOR_RES    480
 #define UI_VER_RES    320
+/* 3.5C capacitive GT911 (ESP32-3248S035C). GPIO33 is I2C SDA, not TOUCH_CS.
+ * Backlight is GPIO27; INT is GPIO21 — they are NOT the same pin. */
+#define CYD_GT911_SDA  33
+#define CYD_GT911_SCL  32
+#define CYD_GT911_INT  21
+#define CYD_GT911_RST  25
 #else
 #define TFT_BL_PIN 21
 #define SCREEN_WIDTH  240
 #define SCREEN_HEIGHT 320
 #define UI_HOR_RES    320
 #define UI_VER_RES    240
-#endif
+/* 2.8" CYD: dedicated SoftSPI touch bus. */
-
 #define CYD_TOUCH_IRQ  36
 #define CYD_TOUCH_MOSI 32
 #define CYD_TOUCH_MISO 39
 #define CYD_TOUCH_CLK  25
 #define CYD_TOUCH_CS   33
+#endif
 
 /* Map 320x240 design coordinates onto the active UI resolution (identity on 2.8"). */
 #define UX(x) ((int)(((long)(x) * (UI_HOR_RES)) / 320))
@@ -28,5 +34,12 @@
 #define UW(w) UX(w)
 #define UH(h) UY(h)
 
+/* Partial frame buffer: 3.5 needs smaller ratio to fit DRAM. */
+#if defined(CYD_BOARD_3248S035)
+#define DRAW_BUF_DIV 20
+#else
+#define DRAW_BUF_DIV 10
+#endif
+
 
 #define PIR_PIN 22

platformio.ini

@@ -55,19 +55,26 @@ build_flags =
 
 extra_scripts = pre:copy_lv_conf.py
 
-; Optional 3.5" CYD ESP32-3248S035 (ST7796 resistive). Default remains [env:cyd].
+; Optional 3.5" CYD ESP32-3248S035C (ST7796 + GT911 capacitive). Default [env:cyd].
 ; Build: pio run -e cyd_35r
+; Keep TOUCH_CS=-1 — GPIO33 is GT911 SDA, not resistive touch CS.
+; TFT_BL=GPIO27 (not 21 — 21 is GT911 INT). See ../CYD_PROJECT_GUIDE.md
 [env:cyd_35r]
 extends = env:cyd
+build_unflags =
+  -DILI9341_2_DRIVER=1
+  -DTFT_WIDTH=240
+  -DTFT_HEIGHT=320
+  -DTFT_BL=21
+  -DLV_MEM_SIZE=49152
 build_flags =
   ${env:cyd.build_flags}
-  -UILI9341_2_DRIVER
   -DST7796_DRIVER=1
-  -UTFT_WIDTH
-  -UTFT_HEIGHT
   -DTFT_WIDTH=320
   -DTFT_HEIGHT=480
-  -UTFT_BL
   -DTFT_BL=27
   -DCYD_BOARD_3248S035=1
-
+  -DUSE_HSPI_PORT
+  -DSUPPORT_TRANSACTIONS
+  -DTFT_RGB_ORDER=TFT_BGR
+  -DLV_MEM_SIZE=32768

src/main.cpp

@@ -7,7 +7,7 @@
 #include "ui.h"
 
 static constexpr uint32_t DRAW_BUF_SIZE =
-    (SCREEN_WIDTH * SCREEN_HEIGHT / 10 * (LV_COLOR_DEPTH / 8));
+    (SCREEN_WIDTH * SCREEN_HEIGHT / DRAW_BUF_DIV * (LV_COLOR_DEPTH / 8));
 static uint32_t draw_buf[DRAW_BUF_SIZE / 4];
 
 void setup() {

src/touch.cpp

@@ -3,10 +3,13 @@
 
 #include <Arduino.h>
 
+#if defined(CYD_BOARD_3248S035)
+#include <Wire.h>
+#endif
+
 /**
- * SoftSPI XPT2046
+ * 2.8": dedicated SoftSPI + BL/TR diagonal fix.
- * BL↔TR 是矩形主对角线镜像（XY 对调），不是 180°（180° 会搞成 TL↔BR）。
+ * 3.5C (3248S035C): capacitive GT911 on I2C SDA33/SCL32/INT21/RST25.
- * 先按 rot2 得到旧 UI，再做对角修正，反变换喂给 LVGL 270。
  */
 
 int16_t g_dbg_phys_x = -1;
@@ -15,6 +18,173 @@ int16_t g_dbg_logic_x = -1;
 int16_t g_dbg_logic_y = -1;
 bool g_dbg_touch_down = false;
 
+static int16_t clampi(int32_t v, int32_t lo, int32_t hi) {
+  if (v < lo) {
+    return (int16_t)lo;
+  }
+  if (v > hi) {
+    return (int16_t)hi;
+  }
+  return (int16_t)v;
+}
+
+#if defined(CYD_BOARD_3248S035)
+
+/* Minimal GT911 — no config rewrite (TAMC setResolution can hang Wire). */
+static uint8_t s_gt_addr = 0x5D;
+static constexpr uint16_t GT_POINT_INFO = 0x814E;
+static constexpr uint16_t GT_POINT_1 = 0x814F;
+
+static bool gt_write8(uint16_t reg, uint8_t val) {
+  Wire.beginTransmission(s_gt_addr);
+  Wire.write((uint8_t)(reg >> 8));
+  Wire.write((uint8_t)(reg & 0xFF));
+  Wire.write(val);
+  return Wire.endTransmission() == 0;
+}
+
+static bool gt_read(uint16_t reg, uint8_t *buf, uint8_t len) {
+  Wire.beginTransmission(s_gt_addr);
+  Wire.write((uint8_t)(reg >> 8));
+  Wire.write((uint8_t)(reg & 0xFF));
+  if (Wire.endTransmission(false) != 0) {
+    return false;
+  }
+  const uint8_t n = Wire.requestFrom(s_gt_addr, len);
+  if (n != len) {
+    return false;
+  }
+  for (uint8_t i = 0; i < len; i++) {
+    buf[i] = Wire.read();
+  }
+  return true;
+}
+
+static bool gt_probe(uint8_t addr) {
+  Wire.beginTransmission(addr);
+  return Wire.endTransmission() == 0;
+}
+
+/* TAMC-compatible address select: INT low => 0x5D, INT high => 0x14 */
+static void gt_hw_reset(bool addr_0x14) {
+  pinMode(CYD_GT911_INT, OUTPUT);
+  pinMode(CYD_GT911_RST, OUTPUT);
+  digitalWrite(CYD_GT911_INT, LOW);
+  digitalWrite(CYD_GT911_RST, LOW);
+  delay(10);
+  digitalWrite(CYD_GT911_INT, addr_0x14 ? HIGH : LOW);
+  delay(1);
+  digitalWrite(CYD_GT911_RST, HIGH);
+  delay(5);
+  digitalWrite(CYD_GT911_INT, LOW);
+  delay(50);
+  /* Backlight is GPIO27 — leave INT as input for polling / optional IRQ. */
+  pinMode(CYD_GT911_INT, INPUT);
+  delay(50);
+}
+
+static bool gt_find_addr() {
+  for (uint8_t a : {uint8_t(0x5D), uint8_t(0x14)}) {
+    if (gt_probe(a)) {
+      s_gt_addr = a;
+      return true;
+    }
+  }
+  return false;
+}
+
+void touch_init() {
+  Serial.println("Touch: GT911 I2C capacitive (3.5C) minimal");
+  Wire.begin(CYD_GT911_SDA, CYD_GT911_SCL);
+  Wire.setClock(100000);
+#if defined(WIRE_HAS_TIMEOUT) || defined(ESP32)
+  Wire.setTimeOut(50);
+#endif
+
+  if (!gt_find_addr()) {
+    Serial.println("GT911 not found — hw reset 0x5D");
+    gt_hw_reset(false);
+    if (!gt_find_addr()) {
+      Serial.println("GT911 not found — hw reset 0x14");
+      gt_hw_reset(true);
+      gt_find_addr();
+    }
+  }
+
+  Serial.printf("GT911 probe 0x5D=%s 0x14=%s using=0x%02X\n",
+                gt_probe(0x5D) ? "OK" : "no", gt_probe(0x14) ? "OK" : "no",
+                s_gt_addr);
+  Serial.printf("GT911 SDA=%d SCL=%d INT=%d RST=%d\n", CYD_GT911_SDA,
+                CYD_GT911_SCL, CYD_GT911_INT, CYD_GT911_RST);
+}
+
+void touch_read_cb(lv_indev_t * /*indev*/, lv_indev_data_t *data) {
+  uint8_t info = 0;
+  static uint32_t last_log = 0;
+  const bool do_log = (millis() - last_log > 200);
+
+  if (!gt_read(GT_POINT_INFO, &info, 1)) {
+    data->state = LV_INDEV_STATE_RELEASED;
+    g_dbg_touch_down = false;
+    if (do_log) {
+      last_log = millis();
+      Serial.println("TouchProbe GT911 I2C err");
+    }
+    return;
+  }
+
+  const uint8_t touches = info & 0x0F;
+  const bool buffered = (info & 0x80) != 0;
+
+  if (!buffered || touches == 0) {
+    if (buffered) {
+      gt_write8(GT_POINT_INFO, 0);
+    }
+    data->state = LV_INDEV_STATE_RELEASED;
+    g_dbg_touch_down = false;
+    return;
+  }
+
+  uint8_t pt[7];
+  if (!gt_read(GT_POINT_1, pt, 7)) {
+    gt_write8(GT_POINT_INFO, 0);
+    data->state = LV_INDEV_STATE_RELEASED;
+    g_dbg_touch_down = false;
+    return;
+  }
+  gt_write8(GT_POINT_INFO, 0);
+
+  const int16_t raw_x = (int16_t)(pt[1] | (pt[2] << 8));
+  const int16_t raw_y = (int16_t)(pt[3] | (pt[4] << 8));
+
+  /* Native 320x480 → LVGL 270. Mirror long axis so L/R matches UI
+   * (else preset 3 hits 10). Resulting UI ≈ (H-1-raw_y, raw_x). */
+  const int16_t nx = clampi(raw_x, 0, SCREEN_WIDTH - 1);
+  const int16_t ny = clampi(raw_y, 0, SCREEN_HEIGHT - 1);
+  const int16_t feed_x = (int16_t)((SCREEN_WIDTH - 1) - nx);
+  const int16_t feed_y = (int16_t)((SCREEN_HEIGHT - 1) - ny);
+  const int16_t ui_x = (int16_t)((SCREEN_HEIGHT - 1) - ny);
+  const int16_t ui_y = nx;
+
+  g_dbg_phys_x = raw_x;
+  g_dbg_phys_y = raw_y;
+  g_dbg_logic_x = ui_x;
+  g_dbg_logic_y = ui_y;
+  g_dbg_touch_down = true;
+
+  if (do_log) {
+    last_log = millis();
+    Serial.printf("Touch HIT GT911 raw(%d,%d) ~ui(%d,%d)\n", raw_x, raw_y,
+                  ui_x, ui_y);
+  }
+
+  data->point.x = feed_x;
+  data->point.y = feed_y;
+  data->state = LV_INDEV_STATE_PRESSED;
+}
+
+#else
+
 static void soft_write(uint8_t data) {
   for (int i = 7; i >= 0; --i) {
     digitalWrite(CYD_TOUCH_MOSI, (data >> i) & 1);
@@ -49,16 +219,6 @@ static uint16_t xpt_read(uint8_t cmd) {
   return v;
 }
 
-static int16_t clampi(int32_t v, int32_t lo, int32_t hi) {
-  if (v < lo) {
-    return (int16_t)lo;
-  }
-  if (v > hi) {
-    return (int16_t)hi;
-  }
-  return (int16_t)v;
-}
-
 void touch_init() {
   pinMode(CYD_TOUCH_CS, OUTPUT);
   pinMode(CYD_TOUCH_CLK, OUTPUT);
@@ -94,8 +254,6 @@ void touch_read_cb(lv_indev_t * /*indev*/, lv_indev_data_t *data) {
   x = clampi(x, 0, SCREEN_WIDTH - 1);
   y = clampi(y, 0, SCREEN_HEIGHT - 1);
 
-  // 旧 UI（LVGL270）：(y, 239-x) — 该空间里 BL↔TR，做主对角线镜像
-  // (ux,uy) -> (uy*(319/239), ux*(239/319))
   const int32_t old_ux = y;
   const int32_t old_uy = (SCREEN_WIDTH - 1) - x;
   int16_t ui_x = clampi((old_uy * (UI_HOR_RES - 1)) / (UI_VER_RES - 1), 0,
@@ -103,7 +261,6 @@ void touch_read_cb(lv_indev_t * /*indev*/, lv_indev_data_t *data) {
   int16_t ui_y = clampi((old_ux * (UI_VER_RES - 1)) / (UI_HOR_RES - 1), 0,
                         UI_VER_RES - 1);
 
-  // 反变换喂 LVGL，使最终落在 (ui_x, ui_y)
   const int16_t feed_x = (int16_t)((SCREEN_WIDTH - 1) - ui_y);
   const int16_t feed_y = ui_x;
 
@@ -123,3 +280,5 @@ void touch_read_cb(lv_indev_t * /*indev*/, lv_indev_data_t *data) {
   data->point.y = feed_y;
   data->state = LV_INDEV_STATE_PRESSED;
 }
+
+#endif